"Telecard" is a provider that provides only high-quality TV channels. If you want to pay for what you use, then this provider is for you. Broadcasting passes through the Orion Express satellite operator, which supplies only the best Russian and foreign channels. Most Russians have already switched to Telekarta, as this operator has set rather low prices for both installation and use.
Of course, setting up "Telecard" and its installation will be paid. Many people do not want to pay extra, but will try to install everything themselves. This is what will be discussed now. Let's look at how the "Telecard" is configured.
Favorable conditions for the installation of "Telecards", checking your locality
First we need to check how the satellite dish will work in your area. It should be noted that this operator is broadcasting from the Intelsat-15 satellite (85, 15 ° -point in geostationary orbit).
You will need to consider the coverage area. If your area falls into the reception area, then you will need a fairly small dish (diameter - 0.6 meters). Another case - you did not get into this zone. What to do? To do this, you will have to purchase a satellite dish of a larger diameter. You need to know this before buying a satellite TV kit.
So, you found out everything and went to the store. After purchasing a satellite dish, it will need to be configured. How to do it? We need to figure out how to point the dish so that it hits the satellite. With the help of a compass, this cannot be determined, since it will show a completely different value. In order to successfully set up the "Telemap" to the satellite, you must determine the exact value of the geomagnetic declination in the place where you are installing.
Coordinates
If you want to determine the exact value, you can call 8 (800) 100-104-7, where the operator will indicate the desired coordinates for your locality. Tuning the "Telecard" antenna will be much faster in this case. But, unfortunately, there are many reviews on the Internet that the operator says not quite the correct coordinates, which, in turn, makes it difficult to set up.
You can, of course, try to call the operator, but if he specifies the wrong value, then you will lose a lot of time. You can go the other way, which will clearly demonstrate how to point the plate. To youyou need to go to the Satellite Finder site, where Google Maps will show the direction. How to see it? Everything is very simple. First, we look for our city and indicate the exact place where the satellite dish will be installed. After that, we indicate the satellite to which we need to tune in. After such simple manipulations, the green line will indicate the direction.
The "Telecard" dish will be set up at the following coordinates:
- The magnetic bearing for the compass is 122.4 degrees.
- Converter rotation angle -29.9 degrees.
You must understand that the higher you install the satellite dish, the more accurate the signal will be. Of course, it can be installed low if there are no obstacles in the direction of the satellite (tall buildings, forests, etc.).
Installing a satellite dish
On the Internet you can find many different instructions on how to install a satellite dish. Of course, they all fit, as the most important thing is to securely mount the device. How to do it?
We will need:
- Universal dowels ZUM 12x71.
- Secrets.
- Several large bolts (75mm).
- Level.
It is necessary to mount a satellite dish on a pipe section that is located vertically upwards. You can check it with a level. During installation, you will need to cut the antenna cable and mount F-type connectors at the ends. Next, you will need to attach the bracket.
Starting to assemble the satellite dish. We connect the cable and turn the converter so that it is tuned to the satellite.
Last step. Install the satellite dish on the bracket. We need to fix it, but do not tighten the nuts too much. This way we can move it around until we are sure the setup is complete.
More detailed instructions can be found on the "Telecards" website. Professional masters from a to z will tell you how to properly install the dish.
Setting up "Telecard" channels
Before connecting all the wires, you must make sure that the satellite receiver and TV are turned off or not even connected to the network. You can connect the receiver via SCART or "tulips".
After connecting, you can turn on the TV with the receiver. To connect to the channels provided by the "Telecard", you need to switch the TV to the "AV" mode. As a rule, when you turn it on for the first time, a picture appears that indicates that the receiver is working, but the antenna is not tuned. In this case, self-configuration is also possible. "Telecard" will be activated by remote control. We go to the menu and go to the item "Antenna settings".
If you have not fully configured the satellite dish, then the readings should be as follows:
- Signal strength is about 45 percent.
- Signal quality is about 5 percent.
With such indications, you will not be able to seetelevision. To get a really high-quality signal, you need to aim for high values (90 percent power and 70 percent quality).
Of course, a pretty good image can be obtained even with a signal quality of 50 percent. But if you get high values, then bad weather won't stop you from watching TV comfortably.
Additional antenna tuning: how to increase performance
If the coordinates that the operator gave you or that you saw on the site did not work, then an additional "Telecard" setting is simply necessary. The essence of the method is simple and clear, but with the help of it we can get a better signal.
So, what is this method? We need to turn the antenna a little. After each such step, you need to give 5 seconds for the receiver to process the signal and tune in to the satellite. Of course, after that you will need to look at the new values that will be shown on the TV. Setting up the "Telecard" is a fairly simple, but long process. If you can't find a suitable value when you turn the antenna horizontally, you should also try vertical turns. Remember, with an increase in power comes an increase in the quality of signal reception.
If you have received suitable values, then we can assume that the setup of the "Telecard" channels is over. It remains only to tighten all the bolts and move on to watching TV.
How long does it take to set up a satellite dish
So, the high-quality tuning of the "Telecard" antenna was made. On their own, beginners will be able to do three hours of painstaking work. Of course, if you find the correct coordinates right away, it will save a lot of time.
Professionals can install in an hour. As they say, beginners can fiddle with it for a long time, but eventually set it up. Everyone is able to install a satellite dish, you just need to have a little patience and everything will work out.
Where is the best place to buy a satellite TV set
It is better to buy all the necessary items from official suppliers. They usually have the opportunity to check the equipment, and during installation you will not doubt its performance. You can also immediately activate the "Telecard" card.
Conclusion
As you saw for yourself, there is nothing complicated in setting up "Telecards". It only looks laborious at first glance, but in fact, after a few hours you will receive a fairly high-quality TV broadcast. Remember that before installation, you need to find out which dish to buy (whether you are in the visibility zone) and whether there are any obstacles in the path of the signal. This way you will protect yourself from problems in the future. If you do not want to do this, then it is better to order the installation from the official Telecard suppliers.
