The design of ceiling lights presented on the shelves of electrical goods stores is quite extensive. However, no matter how beautiful an ordinary chandelier is, the principle of its operation is always the same - some of the bulbs turn on from one key, some from another. But I want something new and interesting. In addition, in the evening, especially in winter, when it gets dark early, it is not very convenient to turn off the light and get to the bed by touch. Sometimes even thoughts appear to hold a switch to the bed so as not to suffer. In such cases, a good solution would be to purchase a remote-controlled LED chandelier, the connection and repair of which will be discussed in today's article.
The principle of operation and the device of ceiling lights with remote control
Scheme of such a chandelierincludes 2 groups of LEDs - main and decorative. The first is designed for lighting and most often has a cold or warm white tint. The second, decorative, can be either monophonic or multi-color. It serves to create a certain atmosphere and can work both in soft glow mode and in color music.
The correct operation of both groups is provided by controllers connected to the signal receiver from the remote control, but there is also the possibility of manual control. You can connect the LED chandelier to a two-gang switch or the supplied control unit, which is mounted in place of a simple circuit breaker.
Below is a video review of one of these devices with a remote control.
Things to know when installing: safety instructions
When starting such work, you should remember the safety rules in its production. Connecting the LED chandelier to the network begins with a complete de-energization of the line to which the room is connected. To do this, you must turn off the machine going to it. You should not hope that it is enough to press the breaker key to relieve the voltage. After all, it is not known which "specialist" performed the installation. It is possible that the switch opens not the phase conductor, but the neutral conductor.
Further, the wires emerging from the ceiling are stripped and parted in different directions to prevent a short circuit. Now you can apply voltage and find the phase wire (if the switch is two-key, there will be 2 of them) andmark it. After that, the voltage is turned off again, a control check of its removal by the indicator is performed. Only after all the above steps have been completed, you can start connecting the LED chandelier.
Mounting the lighting fixture on a single-gang switch
In this case, 2 or 3 (if grounded) wires will come out of the ceiling. At the same time, the yellow-green core is connected to the chandelier body if it is metal. It is better to connect wires (supplying and from the lamp) not to the usual twist, but using screw terminals or self-clamping WAGO. In this case, their design should be chosen depending on the type of wire. For flexible cores, you will have to purchase more expensive products with a mechanical clamp (reusable). If you use a rigid copper or aluminum cable, you can use disposable self-clamping.
After the connections are made, you can apply voltage and check the performance of the chandelier. If the connection of the LED chandelier with the remote control is correct, close and fix the decorative cover.
Connecting fixtures to a two-gang switch
Here the algorithm of work is almost the same, with slight deviations. When searching for a phase, you should first leave only one key on. Having marked the phase coming from it, check the second one and also mark it.
When connecting an LED chandelier with a remote control, you need topay attention to the color of its wires. There should be two identical - phase conductors will be switched to them, and one different for zero. Otherwise, all actions are identical.
Important! Regardless of whether work is carried out under voltage or without it, it is necessary to use only high-quality tools with intact insulation. After all, it is not known who would come up with the idea to turn on the machine in the shield, especially if it is located in the stairwell. We in Russia should not be surprised at such things.
Mounting the LED control box
Some models are equipped with a special dimmer. It provides the ability to reduce the intensity of the light flux. Also, the device allows you to switch modes and change the color. To install it, you will need to dismantle the switch, and connect the regulator instead. It is not difficult to do this - just look at the diagram, which is contained in the technical documentation of the device. The very connection of the ceiling LED chandelier with a control panel is identical to the previous option.
If you draw parallels, then the lighting fixture with a remote control is more convenient to use. Additional comfort is provided by the control unit, however, the more nodes, the lower the reliability - this is an indisputable fact. Therefore, if there is a choice between an LED chandelier with a separate regulator and without one, it is better to stop at the second option.
Recently, ceiling lights are gaining popularitycontrolled from a smartphone. Their cost is much higher, but there is not much difference between them and devices with remote control. Then the question arises - is it worth buying expensive equipment if the cheaper one has almost the same functionality?
Height Adjustable Lights
Such devices can be used for a dining area or a desktop in an office. This is quite convenient when you need to increase the intensity of lighting in a specific area without disturbing others. There are no significant differences in installation with the previous options. The strength of the fastening, as well as the correct connection of the LED chandelier with a height regulator, are checked identically. Exceptions are devices equipped with special motors. They may contain not 2, but 3 controllers. One of them at the same time works with the mechanism of automatic lifting / lowering of the lighting device. The cost of such ceiling lights is quite high. Perhaps that is why they have not received too wide distribution in Russia.
Some tips for buying a ceiling light
In order for the LED chandelier to please with uninterrupted operation for a long time, when choosing it, you should pay attention to some nuances:
- First you need to inspect the packaging. A self-respecting manufacturer will not put a product in a faceless gray box - it should be solid and dense. It should contain details, a link to the site,contact numbers.
- It is mandatory to check two main documents - certificates of conformity and quality. And if the second one can be drawn up according to the standards of the country of origin, then the second one must be marked with Russia.
- Check that the warranty card is filled out correctly. It contains marks on the date of sale, seal and signature of the seller.
- The cash receipt must be kept - without it, you can forget about warranty repairs.
What you should know about lamp repair
Like any equipment, such devices can fail. And sometimes this happens immediately after connecting the LED chandelier. It's annoying, but not fatal. The most common malfunctions of such equipment and their causes should be considered:
- The chandelier reacts to the switch, but does not "see" the remote control - the batteries are dead, the remote control or receiver is out of order.
- The lamp randomly changes modes - a malfunction of the control unit.
- No reaction to the switch and remote control - no power, burnout of the neutral wire.
- One of the modes does not work - the corresponding controller needs to be replaced.
Any breakdown can be fixed or a failed node can be replaced. The main thing is to approach this work with all responsibility and accuracy.
Closing word
Connecting an LED chandelier is no different from a regular one. Their differenceonly in the presence / absence of electronics and cost. This means that if the home master is at least superficially familiar with electrical installation, this work will not be difficult for him, and the mounted ceiling appliance will please the eye with soft and comfortable light for a long time. After all, it is for this that such equipment is purchased.
